We configure the gpon router (using the example of a device for mgts). Proper configuration of MGTS routers How to open the settings of the MGTS gpon router

The technology of passive optical networks (PON) has been used for quite a long time in building networks of various sizes and purposes due to its reliability and stability. It received several branches depending on the final destination: Ethernet PON, Broadband PON and others.

Recently, GPON technology has begun to gain momentum among users

Until recently, the development of optical networks was not so accessible due to the high cost of equipment. Recently, prices have begun to decline, and now “optics in every home” is becoming the best option for everyone, given the other advantages of optics compared to twisted pair and other even less reliable technologies.

To connect subscribers to the Internet, the MGTS provider uses Gigabit PON, or GPON, the most convenient and stable technology for building optical networks today.

When concluding an agreement, MGTS provides for use GPON routers already configured for use with a specific provider. But there are times when the device is reset due to a power surge, or the settings are reset by accident, or, finally, the user may simply need to change the Wi-Fi password.

Setting up an optical GPON router basically resembles setting up a conventional router and consists of the following steps:

• Login to the router management page;
• creating a wireless access point and protecting it with a password.

Details can be studied using the Sercomm RV-6688 GPON router as an example.

Login to the management interface

To configure, the router is connected to the computer via the supplied cable and lan port. An optical patch cord does not need to be connected in this case.

In the address bar, enter the IP of the setup interface: 192.168.1.254. The default login and password is admin / admin, but if the device is flashed or configured by MGTS employees, then mgts / mtsoao is possible. You do not need to select the connection type - it is included in the firmware of the router.

Setting up wireless points

This model, provided by the MGTS provider, supports the ability to create up to four separate wireless networks, including a guest network that will not have access to the local area. Before setting up, check that the DHCP server is enabled on the router. This is located in the "LAN" - "Basic parameters" section and is necessary for the correct distribution of IP addresses to end devices.

Wi-Fi on a GPON router from MGTS is configured as follows:

1. In the "Settings" menu, go to the "Wireless Network" section, then to "Basic Settings";
2. Enable the wireless network with a tick in the appropriate item (or make sure that it is enabled);
3. Assign SSID - point name.

The rest of the parameters can be left unchanged. But it depends on your conditions: if there are other Wi-Fi routers nearby, you may need to select a channel with a different frequency. Also with the signal level: if your GPON router will be at a distance from the receiving devices, then it would probably be better to select the "High" value in the list.

To install protection on the "Security" page, in the drop-down list of network identifiers, we find the name of the newly created point. The rest of the parameters can be left as default, except for the password. Assign a strong password, preferably including both letters and numbers. After that, you need to save the customized configuration.

Conclusion

As you can see, setting up a GPON router from MGTS is no more difficult than similar actions with any other router. If you need, for example, change the password for Wi-Fi, our instructions will help. Who did not help - you can always contact us in the comments for help in solving the problem.

The list of the most famous Moscow telecommunications companies includes MGTS.

The abbreviation of this company stands for Moscow City Telephone Network.

The company is developing rapidly, and recently it has shown great success in providing services for organizing access to the Internet to its subscribers at high speeds: 3G / 4G networks.

The advantage of the company in front of users is that users can purchase a modern multifunctional router, which is very popular among subscribers for its high technical characteristics.

What is a router from MGTS

This company has been operating in the field of telecommunications services for quite a long time, more than fifteen years.

But the provision of routers for distributing the Internet began not so long ago, in 2013. Even then, the company's routers gave very high performance. And now the powerful performance of the router is not inferior, and often surpasses the Internet devices of competitors.

A router (router) is a telecommunications device that provides subscribers with a connection to television, telephone, and also to access the Internet.

The principle of operation of the router is based on the fact that it transmits a signal that gives connected devices.

The company has a wide range of routers for distributing a mobile network. Users can choose the model that suits them for successful use.

The company's routers have a surprisingly low cost, for which you can get Internet without restrictions.

The average speed of a company's Internet packet for a router can range from 30 Mbps to 200 Mbps.

In addition to providing Internet services, the company is engaged in providing telephone connections and television networks, with a large selection of TV channels.

So, two hundred television channels are available to users.

The most popular routers from MGTS

At the moment, one of the most popular models is the zte mf30 router. This model has the following advantages: reasonable price, high quality and great functionality.

The average cost of this router is approximately 2100 rubles and above.

For this cost, users receive the following services and features:

• subscribers will be able to connect several devices to one router at once, and combine them into one common network. So, it is possible to connect up to five devices;
• portability, while the router can be turned on and operated without being connected to the electricity network;
• the ability to work through a secure network using WEP, WPA or WPA2 technologies;

Such technologies help protect the network from scammers. So, other users who do not know the password from your device will not be able to crack the protection and connect to the router.

• use of the 3G module, which allows distributing the Internet and localizing the network between connected devices;
• the compactness of the router makes it possible to use it even when transported in a bag or pocket. The user can always have a router with him and have access to the Internet at any time;
• The router has an additional connector for additional devices. It can be used as a storage device when using an external device such as micro-SD.

Attention! In addition to the advantages that the router has a lot of, it should be noted that it is not without its drawbacks. At the routerztemf30 is a weak battery with a capacity of 1500 mAh, which allows you to work without the mains for about six hours.

The disadvantages also include a weak factory antenna, which cannot be amplified.

The external characteristics of the case and the interface of this router meet the standards, like all the main routers available on the telecommunications market.

The router control buttons are located on the side faces of the case, and the USB and charging port is located at the bottom.

There are also 4 indicators on the router that signal its operating status:

1. Battery charge.
2. signal level.
3. Job status.
4. The mode of the network being used.

Remember! The color of the last indicator indicates the status of receiving and connecting the signal, as well as how the indicator is lit (steady or blinking) indicates the network in which the user is working.

Another router from MGTS, which is popular with users, is the Sercomm RV6688.

This model is used for home gateway module, GPON optical network.

It is not portable, but powered by an optical cable.

The router is small and looks like a simple device for distributing Wi-Fi.

Despite the simple appearance, this router has a large number of functional features.

The main function of this device is the use of modern technologies for high-speed data transmission via xPON optical communication.

The router also allows you to connect not only four computers on a local network, but also a network connection via an Ethernet port (RJ 45), and several more memory drives (standard 2.0).

The router also allows you to organize the transmission of a video signal using a specialized IPTV technique.

This feature gives the user the chance to create four wireless networks at a time.

The router has two POTS (RJ 11) connectors that allow users to connect additional mobile devices, and still use IP-telephony along with other features, while maintaining high quality communication and high data transfer speed.

Should be clarified that despite the fact that the routers are imported, Russian users have a chance to take advantage of the following advantage: when installing the device, they have access to the factory firmware in Russian.

So, the two presented routers from this Moscow company provide free access to the network both in the form of a portable device and in the form of an installed fixed router in the house.

How to set up an MGTS router

Let's take a closer look at the process of connecting the previously presented routers. Some models have different technology and the ability to connect and install.

For example, to install a zte router, the user does not need any additional tools and software, since all the necessary programs are already in the device's memory.

This configuration of the router is very convenient when connecting.

The router software will be installed automatically, the subscriber only needs to connect the USB cable that comes with the router to the USB connector on the computer.

The operating system of the computer will first of all install the software drivers from the internal memory of the device.

Then the virtual media is detected, on which the branded disk is installed.

Upon completion of the download from the internal memory of the device, the router is ready for use.

To prepare the MGTS zte router itself, you need to use the device's built-in interface.

This is done after connecting the router to your PC, and after going to a special address. You must press the "Enter" button and open the settings menu.

It will not be difficult to understand them, since the settings are designed for all subscribers. Even beginners can easily set up their router.

The menu will be divided into two settings sections: on the left there will be a hierarchical menu where specific parameter settings are located.

In the center is the transition to the bottom of the menu.

For example, to connect a router with the parameters of a wi-fi module, the user needs to go to the "WLAN" tab and open the "Basic" submenu.

The user must select the "Network" tab, then it is possible to proceed to the settings of the main parameters.

When connecting a router model Sercomm RV6688, the connection is configured by the wizard, because the connection of this model is much more complicated than the previous one.

If the router of this model is configured independently, then you need to connect the router to a computer or other device using a cable.

After that, you need to open the browser and type in the address bar a specific address, and go to it.

This will be followed by opening a menu with settings, where you need to enter the following parameters:

• login - admin;
• password is admin.

Then a new window will open, in which the general characteristics are located.

On a note! If an error message appears when entering the data indicated above, then the user can enter the following data: password - mgts, login - mtsoao.

Upon successful completion of these steps, the data of the following characteristics will be opened:

• the name of the router;
• its serial number;
• version of this router;
• software version.

To make a wi-fi connection, the user must do the following:

• go to the parameters at the top of the working area of ​​the screen;
• click on the Wireless network option, where you need to set the desired network settings.

Following these instructions, users will be able to set up the router themselves and access the Internet.

But, if there are problems, you should contact a specialist who will help you properly configure the router.

Where can I buy routers from MGTS

Users can purchase routers in the following ways:

1. Buy on the official website of the company.
2. In stores of telecommunications devices, including company stores, where you can find a large number of routers for connecting to the Internet.
3. Order in the online store. But you should carefully choose the seller, since it is difficult to guarantee the quality of the goods on the Internet.

MGTS provides users with a wide range of high-quality multifunctional devices for quick connection to the network.

Subscribers can only choose a router model for themselves and perform a few simple operations to set up a connection.

The Moscow City Telephone Network, or MGTS for short, is an Internet and digital television provider. The provider connects its subscribers to the fiber optic line, ensuring the comfort of working at maximum speed. For this, special ONT terminals are used. In this article, you will learn how to enter the settings of such an MGTS router.

Login to the web interface

To connect home Internet, MGTS provides its customers with one of two models of wireless Wi-Fi routers that are connected to a fiber optic line:

1. ONT SERCOMM RV6699.

1. ONT ZTE ZXHN 670.

Depending on the model installed specifically for you, entering the router settings will be different. To connect a Wi-Fi router MGTS, check:

1. The provider's network cable was connected to the router's GPON port.
2. The LAN cable connected the LAN port of the router and the computer.
3. The router and PC were turned on.

SERCOMM RV6699

To connect to GPON Wi-Fi router SERCOMM RV6699 from MGTS:

1. Open any browser and enter 192.168.1.254 in the search bar.
2. Enter admin in the Username field.
3. Password too
4. Done, you are logged in.

ZTE ZXHN 670

To enter the settings of the MGTS ZTE ZXHN 670 router:

1. Launch Edge or an alternative browser and enter 192.168.1.1 in the line.
2. Login and password for this router: user, user.
3. Done, the interface is open.

A brief description of how to configure this router can be found in the following video:

Login issues

If accessing the router's admin panel is problematic, there are several solutions:

1. Check the correctness of entering numbers and the absence of unnecessary components in the search bar of the browser.
2. Check if the "Obtain an IP address automatically" setting is set on the computer's network adapter.
3. Return the router to factory settings, as there is a suspicion that someone has changed the default login parameters to their own.
4. Reset Windows network settings
5. Check the LAN cable for damage.

Attentiveness

Pay close attention to what you enter in the address bar. There shouldn't be:

1. Extra values, such as https://www.192.168.1.254.

1. Character substitutions 192.168.I.254.

The main thing is to enter everything correctly, preferably manually without using the auto prompts of the search engine.

DHCP server

Each router is set from the factory to automatically assign a network address to a machine connected to its network. If the computer does not automatically receive an IP address, then it simply will not go online and will not be able to open the web interface and will not configure the home Internet.

To set the parameters correctly:

1. Open the "Run" line with the Win + R command and execute ncpa.cpl.
2. Right-click to open the adapter menu and select Properties.
3. Go to section
4. Choose to receive an automatic IP address.

1. Click OK.
2. Turn off and on the adapter, check the availability of the device on the network.

Reset network settings

You can reset the network to default settings in the Windows operating system. This is useful if an antivirus or software like Tunngle or Hamachi was previously installed, which incorrectly installed their own network adapters in the system, messing up with the basic settings.

To return everything as it was:

1. Press Win + I and go to Network and Internet.
2. Scroll down to the very bottom and select "Network Reset".
3. Confirm your decision, and then check the ability to enter the router.

Router factory settings

If someone used a GPON router before you, he could set his own login and password to enter the web interface. The data can be reset, but all the settings made by the user will fly with them. This means that at least Wi-Fi you will have to raise again:

1. Find the Reset button on the case.
2. Hold it for 10 seconds and hold.
3. The router will reboot (you will understand from the indication) with the factory settings.
4. Try logging in with the default username and password.

Checking the patch cord

You can check the Ethernet cable for damage by ringing with a cable tester or, in the absence of one, by pinging and visually inspecting it.

If you get a result like on the screen, it can mean 2 things:

1. On the way, the signal does not reach the router (the cable or network equipment port is faulty).
2. The router is not registered to the network at this address.

Successful passage of data packets indicates the registration of the router in the network. That is, the computer sees it. If it doesn't work from a browser, try another one.

Conclusion

Wireless routers operating with a fiber optic line are provided to MGTS subscribers free of charge. To enter your personal account, you need to use the address 192.168.1.254 for one device model and 192.168.1.1 for another. Authorization data: admin and user respectively.

ZTE ZXHN F660

(
GPON ONT
) MGTS

How to connect to the WEB interface, standard passwords, Telnet

EVERYTHING WHICH IS WRITTEN IN THIS ARTICLE AND IS DONE BY THE READER IS DONE AT YOUR OWN RISK, WE DO NOT BE RESPONSIBLE FOR POSSIBLE DAMAGE TO THE EQUIPMENT!

To gain access to the WEB interface (muzzle) of this optical terminal (modem, router, access point, etc.), you need to know the login and access password.

This terminal has 2 user profiles Administrator and User.

For each profile, there are basic login / password sets installed by MGTS by default.

Profile: Administrator

Option 1

login: mgts

Password: mtsoao

Option 2

login: admin

Password: admin

Profile: User

Option 1

login: user

Password: user

Option 2

Login: name of your WiFi network (default / Default), for example MGTS_GPON_D790

Password: the default password for the WiFi network of the form 26k265kc

(usually the last 8 characters of the MAC address, in small characters)

login: MGTS_GPON_D790

Password: 26k265kc
Profile: Unknown profile, possibly Administrator
Option 1

login: root

Password: admin

At the beginning of 2018, in the terminal, by default, only one profile is available to the user for terminal settings: Profile: User, Option 2.

The administrator profile (mgts/mtsoao) is disabled by default, but can be temporarily enabled via Telnet or by calling tech. support of the provider company and ask to activate this profile.
But when the terminal is restarted, the profile will turn off again for permanent access through it.
—————————————————————————————————————————

RETREAT

Sometimes you need to reset the terminal settings to factory defaults, and passwords from the WEB face are not suitable, and often the Reset button is not an assistant here, since usually Reset on this terminal simply loads a previously created file with settings to replace the current one. Then you need to do the following: Via LAN or WiFi go to the link http://192.168.1.1/hidden_version_switch.gch

If the default is set Russia version
then select from the dropdown list Default version
and press the button submit.
After restarting the terminal, repeat the operations in reverse order, selecting the mode Russian Version
, after the next reboot, the terminal settings are usually reset to Default and you can try to use the default passwords. ————————————————————————————————————————

Enable the administrator profile (mgts/mtsoao) or assign administrator rights to the profile: User via Telnet.

The Telnet service needs to be started.

(On modern Windows operating systems, the telnet.exe utility is not installed by default.)

This can be done in two ways:

1. Through the command line

2. Through the control panel.

but.
Through the command line:

On a command line running as administrator
, run the command:

pkgmgr /iu:"TelnetClient"

Upon successful installation, we see:

Microsoft Telnet>
b.
Through the control panel. For Windows 10 To launch the control panel, you need to enter in the Windows search (on the taskbar) - Control Panel, and then launch it from the list of results.

Everything, TelNet is running, you can work with it. In the search bar on the taskbar (for Windows 10) enter cmd

, in the list of results, run the Command Prompt program as an administrator.

In the window that opens, enter the Telnet command. If successful, we see the following result. Welcome to the Microsoft Telnet Client
Mode switch character: 'CTRL+]'
Microsoft Telnet>

We enter the command:
?

In response, we get a list of available TelNet commands, we need a command to connect to various nodes, in this particular case, this is the “o” command

Enter your username and password to access via Telnet
Login: root Password: Zte521 (password is not displayed when you type) (sometimes root password option is possible) We see:
BusyBox v1.01 ….(blah blah blah) Enter 'help' for a list of built-in commands. /# We enter the command:
sendcmd 1 DB p UserInfo (displays admin and user passwords)

We see something like this:
"Enable" val="0"
/> "mgs"

/> "mtsoao"

/> "Right" val="1"
/>
"Enable" val="1"
/> "MGTS_GPON_K360"

/> "21g264fc"

/> "Right" val="2"
/>

Parameter:
"Enable" val="0" means that the user is disabled "Enable" val="1" means that the user is connected "Right" val="1" user with admin rights "Right" val="2" simple user (not admin) "Username" and "Password" display the set username and password for each profile. Next, there are two options:
We activate the first user (admin): We enter the command:
sendcmd 1 DB set UserInfo 0 Enable 1 Then:
sendcmd 1 DB save or
We make the second user the administrator: We enter the command:
sendcmd 1 DB set UserInfo 1 Right 1 Then:
sendcmd 1 DB save After the performed operations, we get access to the WEB face

Configuring the MGTS gpon zte f660 router

The ZTE ZXA10 F660 router is a modern network equipment necessary for connecting to the worldwide information network via a fiber optic line (GPON technology). In terms of its functionality, it is both an ONT terminal and a Wi-Fi router capable of distributing the Internet both via an Ethernet cable and via wireless communication with the end device.

In addition to the standard features of the zxa10 f660 router, it also provides IP telephony and the ability to create a local Web server based on the router.

And this article provides step-by-step instructions for setting up a zte zxa10 f660 router from MGTS, and also discusses some of the subtleties of connecting this device.

Router zte zxa10 f660: specifications and design features

The gpon ont zxhn f660 router is an economical mobile Wi-Fi transmitter with a main operating frequency of 2.4 GHz.

The functionality of the router provides a Wi-Fi data transfer rate of up to 300Mbps, while the device supports up to 4 SSIDs with a simultaneous connection of 128 users to each network.

Also, the zte f660 router supports WPS mode, so the device can be used to expand the WiFi zone of another router.

On the back of the router are:

• - standard LAN connectors for connecting to zxa10 f660 devices via an Ethernet cable;
• - two POTS connectors for implementing the IP telephony function (for connecting an RJ-11 telephone cable);
• - two USB connectors for connecting external media (including for updating the device's firmware and organizing a local Web server);
• - POWER connector for connecting the power adapter;
• - on/off buttons for WLAN and WPS functions;
• - RESET button to reset the router to factory settings;
• - switch on / off the router.

The GPON connector for connecting the fiber optic cable provided by the provider can be located both on the back and on the side panel of the zte f660 router.

Connecting a zte f660 modem

1. Connect the power supply (supplied with the device) to a 220V electrical outlet, and its plug into the socket on the rear panel intended for it.

2. Connect the optical cable with the green plug to the port intended for it, and its other end to the socket.

3. Insert the plug of the patch cord (Ethernet cable) into one of the four LAN sockets, and its other end into the network card connector of the computer from which you will enter the settings of the MGTS gpon zte zxa10 f660 router.

When you connect the router to a PC, the indicator corresponding to the active LAN connector should light up on the front panel of the device. If this does not happen, it is recommended check network card settings
on this computer.

How to set up a zxa10 f660 router?

Connecting, testing and configuring optical communications, as a rule, is carried out by specialists from a communications service provider.

If you install the zte f660 optical modem yourself, then call the provider's service department, ask them to set up the equipment and follow the instructions of the specialist.

Router zte zxa10 f660: WiFi setup

1. Launch any Internet browser installed on your computer and enter http://192.168.1.1 in the address bar.

In the field that appears, enter the login: admin, password: admin and enter the setup interface of your device.

2. A menu with tabs will appear in the window that opens: "Status", "Network", "Security", "Application", "Administration".

3. Go to the "network" tab, in the "WLAN" submenu and its "Basic" subsection.

In the "Wireless RF Mode" column, select the "Enabled" option.

• - Next, "Mode" must be set to "Mixed802.11b + g + n".
• - "Country/Region" - "Russia".
• - "Chanel" - "Auto".
• - "Transmitting power" - "100%".

4. Click the "Submit" button, then go to the "Multi-SSID Settings" subsection.

In the "Choose SSID" column, select "SSID1".

• - Check the "Enable SSID" box (Check that this box is unchecked for other SSIDs).
• - Think of a name for your network and enter it in the "SSID Name" field.

5. Click the "Submit" button again and go to the "Security" subsection.

- Here in "Choose SSID" select the first option.

• - Set "Authentication type" to WPA2-PSK.
• - Create a Wi-Fi network password and enter it in the "WPA Passphrase" field.

The password must be unique and contain at least 8 Latin characters. Standard and easy-to-guess passwords (for example, the address of the house) are not recommended to be set in order to avoid unauthorized connections to your WiFi network.

How to change the password from the MGTS zte f660 router?

To set a unique administrator password used to enter the settings of the MGTS gpon zte zxa10 f660 router, go to the "Administration" menu and the "User Management" submenu.

- "User Right" switch to "Administrator".

Enter the old password in the "Old Password" field, and the new password in the "New Password" and "Confirm Password" fields.

Also, before using the zte f660 router, it is recommended to disable the WPS function. To do this, press the corresponding button on the back of the device.

Hello dear readers! Recently, I began to miss the speed of the Internet, and I decided that it was time to switch to modern technologies - GPON fiber optic communication. As in any other case, this requires a router. When concluding an agreement with a provider, I received a MGTS GPON router, the router was configured by the installer upon connection. However, soon all the adjustments for some reason flew off.

Having rummaged through the Internet, I found out that many people have similar problems - the router stops distributing Wi-Fi or you just need to change the default settings. At the same time, most users turn to specialists for relatively large amounts of money, although the setup is not particularly difficult. So I decided to collect and present to your attention the most complete instructions for adjustment of the most popular MGTS routers - ZTE and Sercomm. After studying it, you will surely be able to figure out how to configure GPON on your own.

Setting up a Sercomm router

Sercomm RV6688BCM at MGTS is issued to all new customers, so you most likely have it installed. Sercomm Rv6699 Router from MGTS Manual, wifi? You may need to reconfigure it even just to change your password. And the provider assures you that it’s not easy to do it with your own hands, isn’t it? Well, I dare to assure you that this is not true - and you will see this now.

The procedure is very simple. Proceed according to the following instructions:

Thus, you can configure the distribution of Wi-Fi from the Sercomm router. The options for connecting to the provider are included in the device firmware, they do not need to be changed.

If, after setting up, your computer or smartphone sees the network, but does not receive an IP address, you need to enable the DHCP server in the basic LAN settings in the router interface.

Setting up a ZTE router

The ZTE F660 model is configured in a similar way, there are just a couple of differences:

1. The web interface is available at 192.168.1.1.
2. The menu is in English, which can create some difficulties.

We do everything the same - go to the Network menu, WLAN section. In the Basic settings, set Wireless RF Mode - Enabled, do not touch the rest. In the next settings item, select a name. In the Security section, set a password.

So, in a few simple steps, you can set up Wi-Fi on a router from MGTS. If your model is not covered in the instructions, do not worry - in any case, there should not be big differences. Try and you will succeed!

MGTS upgrades GPON, tariffs and equipment

Recently, GPON from MGTS began to behave simply disgusting - in the evening, Wi-Fi losses can reach 10%, and the response time is under one and a half thousand milliseconds. Not at the peak, it just walks from 150-200 ms to 500-600. In this case, the signal level drops to 1-2 bars in the system tray.

At first I thought that the problem was with the Wi-Fi card, especially since at one time I had a problem that the wooden door in the middle “open” position for some reason extinguished the signal to almost zero. But the new laptop gave about the same picture.

And even approached with a laptop right under the router and still jumps from 30-40 ms to 300-400. Everything works amazingly, of course, just like the doctor ordered, but you need Wi-Fi.

It is obvious that someone else has tuned in to 2.4 GHz and is turning on, or actively using, his hurdy-gurdy in the evening. For during the day or after one in the morning - everything works more or less. So either fence a garland, cascading a Wi-Fi access point, which is not particularly beautiful above the front door; or bend MGTS to change the router.

Almost immediately after installation, I wanted to switch my ZTE ZXHN F660 to Huawei HG8245, but MGTS-sheep turned on Moscow-Dynamo, and even loaded it by phone, which is impossible.

And then it turned out that for some time now MGTS has been replacing old models of GPON routers with a fairly new ONT SERCOM RV6699 model that supports, in addition to the standard 2.4GHz band, also 5MHz. It should be noted that 5GHz in Russia is not as crowded as 2.4, incl. interference should be incomparably less. Although it is already written on the Internet that ONT SERCOM RV6699 also comes without external antennas and expansion connectors, and due to Chinese deshmanism, it does not differ in a particular breadth of coverage. But it seems like it can be set to bridge mode, including if the entornnets do not lie, then this will solve the problem of a garland in the corridor.

True, when calling MGTS, it turned out that this equipment upgrade is available only for customers renting a bandwidth of 100 megabits or more. Because, according to MGTS, the old half-dead kyrogaz is quite enough for the rogue.

And then, just in time, MGTS found an offer valid until the end of the month: 150 megabits for 450 rubles a month. Considering that I am now paying 500 for 50 megabits, the savings are in the face. So I almost managed to jump on the outgoing train, because the tariff was cut tonight, and they promised to change the piece of iron in early November, because. They already have a queue to change equipment.

Setting up a ZTE F660 router from MGTS: step by step instructions

The ZTE ZXA10 F660 router is a modern network equipment necessary for connecting to the worldwide information network via a fiber optic line (GPON technology). In terms of its functionality, it is both an ONT terminal and a Wi-Fi router capable of distributing the Internet both via an Ethernet cable and via wireless communication with the end device.

In addition to the standard capabilities of the ZTE ZXA10 F660 router, it also provides an IP telephony function and the ability to create a local Web server based on the router.

And this article provides step-by-step instructions for setting up the ZTE ZXA10 F660 router from MGTS, and also discusses some of the subtleties of connecting this device.

Router ZTE ZXA10 F660: specifications and design features

The gpon ont zxhn f660 router is an economical mobile Wi-Fi transmitter with a main operating frequency of 2.4 GHz.

The functionality of the router provides a Wi-Fi data transfer rate of up to 300Mbps, while the device supports up to 4 SSIDs with a simultaneous connection of 128 users to each network.

Also, the zte f660 router supports WPS mode, so the device can be used to expand the WiFi zone of another router.

On the back of the router are located.

• - standard LAN connectors for connecting to zxa10 f660 devices via an Ethernet cable;
• - two POTS connectors for implementing the IP telephony function (for connecting an RJ-11 telephone cable);
• - two USB connectors for connecting external media (including for updating the device's firmware and organizing a local Web server);
• - POWER connector for connecting the power adapter;
• - on/off buttons for WLAN and WPS functions;
• - RESET button to reset the router to factory settings;
• - switch on / off the router.

The GPON connector for connecting the fiber optic cable provided by the provider can be located both on the back and on the side panel of the zte f660 router.

Connecting a ZTE ZXA10 F660 modem

Follow the sequence of actions:

1. Connect the power supply (supplied with the device) to a 220V electrical outlet, and its plug into the socket provided for it on the rear panel.
2. Connect the optical cable with the green plug to the port intended for it, and its other end to the socket.
3. Insert the plug of the patch cord (Ethernet cable) into one of the four LAN jacks, and its other end into the network card slot of the computer from which the settings of the MGTS gpon zte zxa10 f660 router will be entered.

ZTE ZXA10 F660 router: WiFi setup

Launch any Internet browser installed on your computer and enter http://192.168.1.1 in the address bar.

In the field that appears, enter the login: admin, password: admin and enter the setup interface of your device.

A menu with tabs will appear in the window that opens: “Status”, “Network”, “Security”, “Application”, “Administration”.

Go to the “network” tab, in the “WLAN” submenu and its “Basic” subsection.

In the “Wireless RF Mode” column, select the “Enabled” option.

• Next, “Mode must be set to “Mixed802.11b + g + n”.
• “Country/Region - “Russia”.
• “Chanel - “Auto”.
• “Transmitting power -“100%”.

Click the “Submit” button, then go to the “Multi-SSID Settings” subsection.

In the “Choose SSID” column, select “SSID1”.

• Check the “Enable SSID” box (Check that this box is unchecked for other SSIDs).
• Think of a name for your network and enter it in the “SSID Name” field.

Click the “Submit” button again and go to the “Security” subsection.

Here in “Choose SSID, select the first option.

• Set "Authentication type" to WPA2-PSK.
• Create a Wi-Fi network password and enter it in the “WPA Passphrase” field.

How to change the password from the MGTS zte f660 router

To set a unique administrator password used to enter the settings of the MGTS gpon zte zxa10 f660 router, go to the “Administration” menu and the “User Management” submenu.

“User Right switch to “Administrator”.

Enter the old password in the “Old Password” field, and the new password in the “New Password” and “Confirm Password” fields.

Also, before using the zte f660 router, it is recommended to disable the WPS function. To do this, press the corresponding button on the back of the device.

Sercomm Rv6699 router from MGTS

Fiber-based GPON technology, actively promoted in Moscow by MGTS, is a really convenient, modern and technologically advanced way of broadband Internet access offered at a reasonable price. In particular, at the time of writing this review, the minimum tariff for the “GPON Home Internet” line was 300 rubles per month for access at a speed of 30 Mbps, and the maximum was 1,600 rubles per month for a speed of 500 Mbps.

The “Services” tab consists of three sections: Firewall, “Telephony” and USB. In the Firewall section, general and fine-tuning of the firewall is performed. First of all, you can choose one of the preset protection levels, or make your own settings.

In the DDNS section, you can configure DDNS servers (there are several providers to choose from) so that other Internet users can connect to you using a dedicated domain name.

In the “Parental Control” section, you can set time limits for networking devices with a specific MAC address, as well as filter access to sites by their URL.

To check the wireless connection in the 5 GHz band, we used the Speedtest application from Ookla installed on the Honor 9 smartphone running the Andro operating system>

Overview of the Sercomm RV6688 GPON router

SC/UPC (Optical interface):

• fiber type - single-mode;
• interface standard - ITU-T G.984.1;
• data reception / transmission speed - 2.488 Gb / s / 1.244 Gb / s;
• fiber optic channel length - up to 20 km.

• frequency - 2.4 MHz;
• standards - IEEE802.11b, IEEE802.11g and IEEE802.11n;
• support for IPv6 - a new protocol using an address length of 128 bits;
• function of manual and automatic selection of channels;
• WPS physical enable button and LED function indicator;
• WEP, WMM, WPS, WPA/WPA2PSK, WPA2PSK and WPA PSK encryption.

tab "Security". Here the user can configure access to his wireless network for each of the created SSIDs separately (authentication type, data encryption method, network access password, security key update interval). The ONT RV6688 router is supplied to MGTS subscribers as a home gateway for the GPON optical network.

The initial setup of the equipment, when connecting a subscriber, is carried out by a specialist of the company. However, there are also cases in which it becomes necessary to change the network name or change the access password. In order to carry out such operations on your own and once again not to call the installer, detailed instructions for setting up the RV6688 are offered.

Worth remembering! The reliability of the network directly depends on the complexity of the access password. To be reliable, it must contain upper and lower case characters and numbers, and its length must not be less than ten characters.

Pay attention to the next moment! If, when trying to connect to a WIFI network, the message “Obtaining an IP address” constantly appears, this means that the “DHCP server” function is disabled on your client terminal. To fix this error you need:

• go to the settings menu of your router;
• go to the "Settings" tab, which is located at the top of the screen;
• on the right side, select the “LAN” section;
• Next, you need to go to the “General Settings” tab and check the box “Enable DHCP server.

Sercomm RV6688 is a home gateway module for GPON optical network. In other words, this is equipment that is installed directly at the subscriber's apartment. In appearance and overall dimensions, the RV6688 resembles a regular WI-FI router. However, this impression is misleading, since this device combines a lot of functions.