Let's say this - if a person does something for the first time, then he can be called a noob in this matter. I have never put a protective glass on my phone! I've only seen this process once. Therefore, you can safely consider me a noob at gluing protective glass. In this article I will answer the question - can a noob stick a protective glass on an iPhone well?
So, the glasses were ordered back in October from Aliexpress. They were not tracked in any way after leaving China. Two months passed, my period of protection was extended at my request. As a result, I opened two disputes and the sellers returned my money. But the Russian Post turned out to be to blame (who would doubt it). A couple of days ago they sent me two notifications, saying that your parcels need to be picked up urgently (they have been in the mail for almost 30 days). That is, the postman stupidly did not deliver the notification.
Started from the first glass for iPhone 6 Plus. I ordered from this link.
The glass was in a foam box. To damage the glass inside, even Russian Post would have to try very hard.
Before my first experience, I watched a video on Youtube about proper gluing - I didn’t learn anything new. The essence of the process comes down to wiping the screen with an alcohol wipe and then carefully placing the glass on the screen.
The box contained not only the glass itself in a special case, but also a double set of small napkins: wet (alcohol) and dry. I wiped the screen with them one by one:
Then I took out the glass, peeled off the protective film by pulling the special label. And he carefully placed the glass. And then I was surprised - it fit perfectly and the air came out on its own within 5-7 seconds. No bubbles or other artifacts were found.
The process turned out to be extremely elementary.
Second glass for iPhone 5S I ordered from another seller. Here it already arrived in a small cardboard box. In addition to the same step-by-step napkins, the kit included a Dust-absorber (dust collector). Why is it needed? I simply did the same thing as with the first glass.
Nuance. The glass for the iPhone 5S is slightly larger than the visible part of the screen, so no matter how you sculpt it (even if not evenly), it will still fit perfectly and cover the entire screen, but the iPhone 6 Plus turned out to be snug in width. Therefore, I recommend extreme care so that the glass does not steal a couple of pixels.
Conclusion: And here is the answer to the question in the title. Yes, anyone can glue a protective glass onto their phone without difficulty or experience. If you are afraid of sticking them sloppily, well, order two pieces. It won’t go to waste anyway – there will be a spare one.
The protective glass on Apple gadgets is designed to protect the devices from damage. Typically, a high-strength chemical composition is used to protect the display from chips and scratches. Some users neglect such protection, but in vain. Protective glass for iPhone 6 and other gadgets can significantly extend the life of your mobile device.
In this article we will look at how to remove the protective glass from iPhone 5 and devices of other versions. We will also pay attention to how to glue protective glass on an iPhone. In addition, we will try to identify the advantages of this method of protecting the display over conventional film.
How to change and how to glue glass - read detailed instructions below.
If we compare the 2 main methods of protecting the iPhone display screen - glass and film - most criteria will be in favor of the first.
The advantages of glass coating are:
- Increased strength with a small thickness of only 0.25 mm.
- The presence of an oleophobic coating that prevents fingerprints from appearing on the display.
- Sometimes - the presence of a nanocoating, which gives increased smoothness to the surface.
- Reliable fastening using silicone elements that prevent the coating from moving and prevent the formation of unevenness and bubbles.
Flexible glass to protect the display of mobile gadgets can also have folded edges. This means that the edges are rounded so the coating is almost invisible. In addition, if the device hits something, the coating will not fall off. So if you are wondering which is the best protective glass, opt for an element with rolled edges.
Removing glass: precautions
Before you get started, there are some rules to consider. First, remember that the glass adheres quite tightly to the display because it is very smooth. But the element is held in place not by glue, but by electrostatic forces. Thus, two perfectly flat surfaces are in close contact, and the glass cannot be removed simply by picking it up with your finger. But you also cannot use a household item, for example, a knife, for this purpose, since there is a risk of damaging the screen or case.
A silicone suction cup will not help in this situation either. If you glue this tool to a damaged coating, a void will form underneath it, and when pressed, it will slide off.
And if the fastening is good, the suction cup will not go anywhere, but another problem will arise. The fact is that the sensor is attached to the body of the gadget using either glue or adhesive tape. The strength of these substances in terms of rupture is much lower than that of glass or touchscreen. Therefore, strong pressure can lead to complete tearing of the display module and damage to its cables. You need to work here carefully and carefully.
How to remove protective glass from iPhone 5S, 4S
Even taking into account the fact that the service life of protective glass is longer than that of films, it also needs to be changed sometimes. The glass comes on a silicone substrate, so it adheres firmly to the display. Removing it will require some skill.
Before removing the protective element, you need to carefully prepare and purchase some tools and materials, namely:
- A spatula (or a thin plastic card), a mediator.
- Silicone suction cup.
- Lint-free cloth.
- A glass cleaner that must contain alcohol.
- Gloves.
Sometimes it happens that all the tools and materials listed above are included with a new protective glass. But this happens quite rarely.
And the glass removal algorithm itself includes the following steps:
1 You need to wash your hands well with soap before starting work, and then dry them. You don't have to do this, but just wear gloves. This is necessary to prevent fingerprints or streaks from appearing on the display. 2 If the glass is damaged, you need to choose the area that is best preserved and has no chips. You need to attach the suction cup to this place, pressing it tightly. 3 You need to place a pick or a spatula in the corner to which the suction cup is attached and pry it off. The edge of the coating should peel off. To do this, you will need to pull the suction cup towards you a little, but not too much. To prevent the screen from falling off. This way we will achieve the goal of forming between the screen and glass short distance. But if you don’t have a suction cup, just insert the pick deeper. 4 As you peel off the glass, deepen the tool. And if the display is large, you can use 2 mediators or spatulas for the procedure, moving them in different directions. 5 And the last step is to pull the suction cup towards you so that the glass completely moves away from the screen. In this case, you can grab its edges with your fingers and do the same.
How to stick glass on iPhone 6 and other devices
For everything to go perfectly, you need to glue the glass in a clean room where there is no dust. Before sticking the glass, you need to take a lint-free napkin or a simple cloth and slightly wet the display with a cleaning agent or alcohol. This is necessary to clean the surface and remove fatty elements from it.
The gluing procedure is carried out as follows:
1 Pick up a new protective covering for the display. As with removal, keep your hands clean and dry. Or you need to wear gloves. 2 Remove the protective film covering the sticky surface. To do this, you need to grab it by the tongue and pull. 3 How to glue the element itself? The glass should be kept as close to the iPhone display as possible so that small particles of debris or dust do not get on it. After all, any surface tends to quickly accumulate dust. 4 Place the glass cover a few millimeters from the display, align and center it. When gluing, you need to act carefully and carefully ensure that all the holes for the keys, speaker and other elements match. 5 Next, the protective glass on the iPhone 5 is lowered closer to the screen. Lightly pressing and smoothing movements smooth out the surface. So easily we were able to glue the glass to the display. 6 The surface is wiped with a dry cloth. 7 Remove the glued element on top that protected the glass.If at the end of the procedure you see small dust particles under the protective element, you can peel off part of the glass and blow them out with a vacuum cleaner or remove them with tweezers. Then you need to glue the element back again. You already know how to re-glue glass.
Now you know how to stick a protective glass on an iPhone. There is nothing complicated in this procedure; replacing glass on an iPhone 5S is as easy as shelling pears. Gluing the protective glass on the iPhone requires careful preparation. And the main thing here is to keep everything clean.
Which is better – glass or film?
The answer is obvious - of course, it is better to opt for glass protection. But the point is not only in impact-resistant properties, but also in durability. One has only to note that glass for iPhone 4 or another version of the gadget costs twice as much as regular film.
So the final choice is up to the user. Think for yourself - what is better - to pay more, but in the future avoid expensive device repairs, or save now, but then shell out a lot of money later. Screen replacement is one of the most expensive types of repair for Apple gadgets. But, on the other hand, film cannot be called a bad option either.
As a result, the summary will be as follows. The film is affordable. It protects the display from minor scratches, removes glare and covers the entire screen. Is a protective film for the iPhone screen necessary, given its characteristics? Absolutely yes. Moreover, its cost is low, and how to stick the film is an even simpler task than in the case of glass.
Glass is an expensive option. It gives glare, but transmits light to the maximum, and also reliably protects against strong falls and deep cracks. And if you have found a way to save money on an iPhone, you will not be satisfied with cheap protection options. In any case, knowing how to save up for an expensive device, you can find funds for good accessories for the iPhone 6S or other device.
Many people may drop their phone during use and carry it in their bag, where, in addition to the phone, there are also sharp objects - for example, keys.
Therefore, it is not surprising that after several months of use, scratches appear on the surface, and in some cases, chips and cracks.
However, using modern technologies, you can achieve an extension of the life of the device. An excellent solution is to purchase and glue protective glass.
Visually, it strongly resembles a film designed to solve similar problems.
But such glass is completely transparent and flexible, and due to its increased density it is considered more durable and reliable.
Price protective screen for a phone is an order of magnitude higher compared to film, but the additional money spent justifies the stated price.
If it is present, the likelihood of the screen suffering from damage is reduced to virtually zero.
Why do you need protective glass?
Read also:Without moisture and dust: TOP-20 protected smartphones ip68
Before you stick a protective glass on your smartphone, let's first get acquainted with its main features.
The main advantages are as follows:
- increased resistance to scratches and damage. Checking this is quite simple - you can easily rub the surface with scissors or a knife. The face covering will not receive any marks;
- absorption of impact energy. Even if the display falls down, its front part will not be damaged. Only cracks in the protective glass will remain on the surface. The structure of the material from which it is made prevents the appearance of splinters;
- reliable fixation. Compared to gluing film, safety glass is easy to glue at home, even if the owner does not have the relevant experience. A special adhesive composition guarantees a strong fixation on the front of the screen. Thus, getting rid of the protective glass will not be easy, which cannot be said about ordinary film, which can be torn off even with a smartphone case.
The use of protective glass is also characterized by a number of disadvantages:
- the device will become heavy and bulky;
- the cost of protective glass is an order of magnitude higher compared to film;
- Extreme care is required during the installation process.
The average display thickness varies from 0.2 to 0.3 mm. The product has 5 base layers:
- oleophobic coating . It is responsible for the comfortable sliding of the user’s fingers across the display, and if fingerprints appear, they can be wiped off with a regular cloth. In addition, the task of the oleophobic coating is to provide comprehensive protection against moisture penetration;
- protective covering . Its purpose is to maintain the integrity of the screen and prevent cracks/scratches;
- anti-reflective coating . Another important layer that prevents dull marks from appearing on the display when using the phone in the sun;
- containment layer . If a situation arises where the user is still able to break it, the containment layer will prevent the appearance of fragments;
- silicone layer . Fixed on the display surface.
How to glue glass on iPhone
Read also:TOP 11 Best Chinese smartphones | Current rating 2019
If you want to familiarize yourself with the correct sequence of actions when gluing protective glass on the 7 series, you must remember that for almost all devices the algorithm of work is the same.
Depending on the name of the glass manufacturer, the contents in the box may vary significantly. As a rule, the kit contains not only glass, but also a microfiber cloth.
In some cases, an alcohol wipe is also present. If, for example, certain materials are not available, you can use alternative means at hand.
So how to properly stick protective glass on a smartphone? The instructions are as follows.
1 If your phone already has old film or glass, you first need to get rid of the coating.
To do this, first remove the cover and then pick up the cover by the edge.
Before performing the procedure, be sure to clean your hands so that you do not leave greasy fingerprints on the surface of the glass during the work process.
If you install them and stick the protective glass on your smartphone, you will see marks every time you use the phone.
2 Prepare your work area in advance.
It can be any flat surface - a table, stool, etc.
To prevent dust and streaks from appearing during the process of gluing the protective surface, we strongly recommend turning on bright light in the room.
3 The next step is preparation. Using cotton pads or an alcohol wipe, thoroughly wipe the surface of the display.
After that, take a microfiber cloth and wipe the screen so that no traces of alcohol, dirt, stains, etc. remain on its surface.
Checking for defects is very simple - just bring the phone screen closer to the light source and check the cleanliness of the coating.
If for one reason or another you cannot completely get rid of dust particles, you should try to collect them using ordinary tape.
Place the sticky side of it on the screen and pull sharply.
Please note that this must be done quickly, since if the tape is slowly peeled off, traces of glue may remain on the surface of the display.
Once the tape is removed, wipe the display again with a dry cloth.
4 Each piece of protective glass includes two films.
First, get rid of the bottom film from the adhesive side.
Offer a protective cover for your display.
Please note that you can only hold it by the edges. Otherwise, marks will remain on the surface.
Align and carefully glue the glass along all edges. Be sure to fit it to the speaker and home button.
Then slowly release the glass - it will begin to stick to the display on its own.
Practice shows that not every person can perfectly glue a new protective glass the first time, since air bubbles may remain under it.
In this case, you can get rid of them with a dry cloth. Just press it on the display towards the edges.
After this, all the air goes outside.
If there is dust under the glass, you need to bend it on the required side and get rid of the dust with tape. Then press the protective glass back onto your smartphone's display.
Now, having read the correct instructions for gluing protective glass on the iPhone 5, 6 and 7 series, you will have the opportunity to further save on service center services and provide comprehensive screen protection yourself.
We suggest watching video instructions from specialists who talk in detail about how to perform all the steps correctly.
How to stick a protective glass on an iPhone screen
Gluing glass with 3D rounding
Read also:TOP 10 Best budget smartphones with optimal price-quality ratio up to 15,000 rubles. | Review of current models in 2019
If you recently purchased a new one, we strongly recommend that you protect it from screen damage, including chips, scratches, and so on.
This is quite easy to do. We bring to your attention an overview of special protective glass with 3D curves.
These products are designed to provide comprehensive protection to the screen surface from damage resulting from severe impact or contact with sharp objects.
The average layer thickness is only 0.23 millimeters, but thanks to the use of a polymer structure, the smartphone can easily cope with strong impacts.
During production, materials are used that are capable of creating a special barrier that quickly cracks, absorbing impact energy, but at the same time guaranteeing high-quality protection for the screen as a whole.
Compared to conventional glass, 3D curved products offer the following advantages:
- Presence of soft edges. Manufacturers use special PET materials to make the edges of the protective surface. This allows you to achieve high-quality and reliable fixation, and the edges will not crumble or crack. This is not only a convenient, but also a safe solution, since the soft edges will not scratch the owner’s hand when, for example, he takes the phone out of his pocket;
- 3D wrap effect. If, in the case of ordinary glass, only the straight part of the display is covered, gluing glass with 3D curves guarantees comprehensive protection of the entire display of the device. Thus, the extreme curved surfaces will be reliably protected;
- Increased level of hardness. Despite the small thickness, the production material has a hardness of 9H. Today, this is one of the few models that fully meets this indicator;
- Minimum thickness. Using ordinary Chinese glass makes the phone more difficult to use. Branded products always have a thickness of just under a quarter of a millimeter, but this is quite enough for the device to receive high-quality and durable protection over a long period of time.
VIDEO: How to remove protective glass from your phone screen? Removing the old broken protective glass
How to remove protective glass from a phone screen? Removing the old broken protective glass
To stick protective glass on at home, you need to follow the algorithm below.
1 Disinfect your hands so that during the process of gluing the glass, no traces of contamination, including dust, remain on the surface of the display.
Place the film on your iPhone so that each cutout matches the position of the protective layer.
Wet the top layer of your film. This should be done carefully. Wetting is done to allow the squeegee to slide freely over the surface of your device.
Using a squeegee, your next task will be to completely remove the liquid towards the left and right edges.
It is important to perform this procedure in such a way that the protection does not stretch across the surface of the base (display).
After complete removal Liquids from under the screen must be wiped dry.
This can be done using a regular napkin. It is highly recommended to ensure that the space between the film and the screen is free of dirt and dust.
Before you start gluing the ends, you need to wait a little.
They should dry out.
The manufacturer notes that this helps simplify the process of attaching the film.
Stick the protection to the ends of your iPhone without stretching the protective layer.
7 At this point the procedure can be considered completed.
Practice shows that the process will take up to ten minutes of free time.
The developers paid attention to every detail, so gluing the film should not be difficult.
Among additional accessories for smartphones, protective glass is perhaps the most necessary component, as it protects the gadget from mechanical damage. Many owners mobile devices Such a popular brand as Apple pays significant sums of money for new phone models, and of course everyone purchases protective glass to minimize the risk of damage to an expensive device. In this short review, we want to answer users’ questions about how to glue protective glass on an iPhone.
Be sure to prepare a clean work area and tidy your hands, they should be perfectly clean. Wipe the device screen with a special napkin and place the phone in front of you. Now peel off the protective film from the glass to reveal the adhesive layer. If we are talking about replacing the protective glass, then after removing the old material, dried glue will remain on the screen, and it will not be easy to remove it. Moisten a cotton pad with pure alcohol, gently, slowly wipe, wipe the surface of the matrix with progressive movements. Do not overdo it, if you press too hard, you can damage the device, then to replace the touchscreen you will have to contact an Apple service center.
- Remember, the most important thing is not to touch the glass with your hands after you have removed the protective film from it, otherwise your fingerprints will remain on the adhesive side, which will ruin appearance gadget.
Jeweller's precision is extremely important in the process of gluing the glass; all edges must coincide with the iPhone screen, so take your time so as not to ruin everything. So, peel off the film from the protective glass and match it to the screen without touching the surface. Now you need to quickly glue the middle of the glass, the edges should lie on their own, all you have to do is smooth it. Thanks to the fact that we cleaned the surface, no bubbles should form, which means you can count on a perfectly smooth mirror surface of the iPhone.
How to glue protective glass yourselfIPhone, and what are the disadvantages?
It is not difficult to stick on protective glass if you follow all the above rules, but such an additional accessory implies certain disadvantages. First of all, it should be noted that the weight of the iPhone will increase, as will the dimensions; if this does not bother you, then feel free to glue protection against mechanical damage to the gadget.
How to stick glass on an iPhone?
Additional protective glass for your phone is a modern alternative to conventional screen films. This accessory will protect your smartphone from all types of mechanical damage to the display (scratches, abrasions, cracks from dropping the device).
If you decide to purchase a protective glass for your iPhone, check out the basic tips for choosing this accessory:
- The thickness of the glass determines the level of protection of the phone from falls and shocks;
- select the type of glass - matte or glossy. The second option is cheaper. Glossy products protect the screen from impacts, but not from scratches;
- Frosted glass completely protects your iPhone from bumps, abrasions, drops and glare.
Installing a protective accessory on your phone screen does not require special skills. Let's take a closer look at how to stick protective glass on an iPhone in a few simple steps.
Step 1: Clean the display
Get your workspace in order. Make sure there is no dust on the surface that could end up trapped under the film. Then open the package and place all the elements on a clean, flat surface.
Clean your smartphone screen using a cloth and glass cleaner. Carefully wipe the surface of the display and wait for it to dry completely. This action will remove even invisible dust particles. Try not to touch the iPhone screen directly anymore, so as not to create new stains and specks of dust. Wipes for initial cleaning of the phone are included with the protective glass.
Step 2. Unpacking the protective glass
The next step is to unpack the accessory and prepare it to stick on your phone. Take the screen and peel off the protective layer, which, once glued, will come into contact with the phone's display. After removing the protective layer, try not to touch the protective glass, otherwise fingerprints will remain on the product.
Step 3. Gluing
Turn the protective glass over to the side that was removed from the film. Place the accessory above the smartphone screen without touching it. Try to match everything as evenly and accurately as possible to avoid uneven gluing.
Further action must be done very quickly. Gradually apply the glass to the iPhone display in the direction from the top of the case to the bottom. Release the film so that the side sections stick to the phone themselves. By cleaning the display well, bubbles will not form.
Step 4. Smoothing the surface
Users do not always know how to stick glass on an iPhone. As a result, the result may not be ideal. To remove small bumps or trapped air, take a piece of microfiber (included with the glass) or a clean cloth and gently wipe the phone, moving from the center of the display to the sides, pressing lightly. In this way, flaws can be eliminated.
A film is also glued to the outside of the protective glass. Remove it immediately after all defects have been eliminated. Now turn on the device and check the responsiveness of the sensor. Normally, the additional screen should not affect the smartphone in any way.
Eliminating errors
If too many dust particles and dirt get under the protective glass during gluing, it will be inconvenient to use the smartphone. The sensor may respond less well to touches, and the appearance of such a phone will not be the best. Many users are wondering how to re-glue the glass on an iPhone and is it possible to do it at all? Yes, you can.
If the accessory does not stick properly the first time, carefully remove it from the display and set it aside on a clean surface. Thoroughly wipe the iPhone screen again and make sure there is no more dust or dirt on it. Only after cleaning the screen, stick the glass again. There is no need to peel off the accessory anymore.
How to remove glass from iPhone?
As a rule, users only need to remove the protective glass in one case - when it breaks during a fall or impact. It is very important to remove the accessory correctly so as not to damage the main display of the smartphone with fragments.
Take a plastic card and use it to pry the edge of the protective glass. Then slide the card under the glass until it is completely removed. This method allows you to create some kind of barrier while waiting for the display and a damaged protective accessory.
